Contribution Assessment of Roadheader Performance Indexes by Analysis of Variance

Mun-Gyu Kim; Chang-Heon Song; Joo-Young Oh; Jung-Woo Cho

doi:10.7474/TUS.2022.32.6.386

All Issue

2022 Vol.32, Issue 6 Preview Page Next Page

Technical Note

Contribution Assessment of Roadheader Performance Indexes by Analysis of Variance 분산분석을 이용한 로드헤더 절삭시험 입출력 인자 간의 기여도 조사

31 December 2022. pp. 386-396

PDF XML

Abstract

To analyze the influence of variables of roadheaders, the linear cutting testing data of pick cutter were collected from the former literatures. The input factors were set up as uniaxial compressive strength, cutting depth, cutting spacing, attack angle, skew angle, and output factors were determined as specific energy, average cutting force, maximum cutting force, average vertical force, and maximum vertical force. After composing a table of the design of experiment (DOE). The contribution level of each factor was calculated by analysis of variance (ANOVA). As a result, the factors having greatest influence on cutting force and specific energy were uniaxial compressive strength and cutting spacing.

Keywords

로드헤더

픽 커터

선형절삭시험

실험계획법

분산분석

로드헤더에 미치는 변수의 영향력을 분석하기 위해 픽커터 절삭시험 관련 참고문헌들을 조사하였고, 수록된 데이터들을 수집하였다. 입력 인자는 일축압축강도, 절삭 깊이, 절삭 간격, 받음각, 비틀림각, 출력인자는 비에너지, 절삭력, 수직력으로 결정했다. 입력 인자와 출력 인자로 분류 후 실험계획법을 작성하였고 분산분석을 이용해 변수들에 대한 기여도를 조사하였다. 그 결과, 절삭력과 비에너지에 가장 큰 영향을 미치는 요인은 일축압축강도와 절삭 간격으로 분석되었다.

키워드

Roadheader

Pick cutter

Linear cutting test

Design of experiment

Analysis of variance

References

Bilgin, N., Yazici, S., and Eskikaya, S., 1996, A Model to Predict the Performance of Roadheaders And Impact Hammers In Tunnel Drivages, Presented ate the ISRM Symposium, Italy.

Bilgin, N., Tumac, D., Feridunoglu, C., Karakas, A.R., and Akgul, M., 2005, The performance of a roadheader in high strength rock formations in Küçüksu tunnel, Proceedings of the International World Tunnel Congress and the 31st ITA General Assembly, Istanbul, Turkey, 7-12 May 2005, pp.815-820

Bilgin, N., Demircin, M.A., Copur, H., Balci, C., Tuncdemir, H., and Akcin, N., 2006, Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results. International Journal of Rock Mechanics & Mining Sciences, 43, 139-156. 10.1016/j.ijrmms.2005.04.009

Jeong, H., Choi, S., Lee, S., and Jeong, S., 2020, Rock Cutting Simulation of Point Attack Picks Using the Smooth Particle Hydrodynamics Technique and the Cumulative Damage Model, Applied Sciences, 10(15). 10.3390/app10155314

Park, J., Kang, H., Lee, J., Kim, J., Oh, J., Cho, J., Rostami, J., and Kim, H., 2018, A study on rock cutting efficiency and structural stability of a point attack pick cutter by lab-scale linear cutting machine testing and finite element analysis, nternational Journal of Rock Mechanics and Mining Sciences, 103, 215-229. 10.1016/j.ijrmms.2018.01.034

Rostami, J., Ozdemir, L., and Neil, D.M., 1994, Performance prediction: A key issue in mechanical hard rock mining. Mining Engineering, 11, 1263-1267.

Rostami, J., 2011, Section 7.1 Rock Breakage, Mechanical, Mining Engineering Handbook, Society of Mining, Metallurgy, and Exploration Engineering Inc (SME).

Restner, U. and Plinninger, R., 2015, Rock Mechanical Aspects of Roadheader Excavation. EUROCK 2015 & 64th Geomechanics ColloquiumAt: Salzburg, Austria, October 2015.

Taguchi, G., and Phadke, M.S., 1989, Quality Engineering through Design Optimization. Quality Control, Robust Design, and the Taguchi Method, 77-96. 10.1007/978-1-4684-1472-1_5

Thuro, K. and Plinninger, R.J., 1998, Geological limits in roadheader excavation-Four case studies, Proceedings of the 8th International IAEG Congress, pp.3545-3552.

Thuro, K. and Plinninger, R.J., 1999, Roadheader excavation performance-geological and geotechnical influences, Proceedings of the 9th ISRM Congress, Paris, pp.1241-1244.

Wang, X., Su, O., Wang, Q., and Liang, Y., 2017, Effect of cutting depth and line spacing on the cuttability behavior of sandstones by conical picks, Arabian Journal of Geosciences, 10, 525. 10.1007/s12517-017-3307-3

Information

Publisher :Korean Society for Rock Mechanics and Rock Engineering
Publisher(Ko) :한국암반공학회
Journal Title :Tunnel and Underground Space
Journal Title(Ko) :터널과 지하공간
Volume : 32
No :6
Pages :386-396
Received Date : 2022-12-06
Revised Date : 2022-12-26
Accepted Date : 2022-12-26
DOI :https://doi.org/10.7474/TUS.2022.32.6.386

Tunnel and Underground Space ISSN:1225-1275(Print) 2287-1748(Online) 터널과 지하공간

All Issue